— Italian Carrara Tiles

September, 2016 Monthly archive


Are messy spills and greasy splatters becoming an unsightly nightmare for you? Or are those stain-prone spots behind your kitchen sink becoming more difficult to clean? Well, there is a great solution that you can consider to ease your problems –a mosaic tile backsplash. With the right color combination and the use of beautiful, translucent glass mosaics, the end result can add sparkle and shimmer to your kitchen.

Mosaic tiles comprised of an array of small tiles that form a cohesive and aesthetically appealing collage pattern. It provides a fantastic visual pop to any space they are utilized in and the only limitations you will encounter are only those set by your own creativity. Read on to find out how you can install a mosaic tile backsplash in your kitchen:


You should turn off all power to any electrical receptacles on the wall you are tiling. Once done, you can proceed to install a temporary ledger. You will need to lay some scrap cardboard on your counters and against the wall to act as a spacer. Now, affix a piece of lumber between the countertop and wall with drywall screws. This is your ledger. Also, ensure that it’s fairly even with the top of the cardboard spacer.

New drywall and other porous surfaces bond well with thinset, but you can still tile over a wall that’s painted. You just need to rough up the surface with a sanding sponge (approximately 80-grit). If you are planning to install translucent tiles over brightly-colored walls, you should prime it with a sealer-primer first. This prevents the color from bleeding through the thinset when you sand.

Mark the Layout

Always select an area that’s considered a natural focal point. Once you picked that out, mark out the centerline on the ledger with some painter’s tape. Next, you can lay out the sheets for the starting area. A general rule of thumb is to leave a 1/8-inch expansion gap at the perimeter. In most cases, you will not be working with a single, large sheet. There are multiple sheets to lay but the process is the same.

Coat, Comb and Smoothen the Thinset

Once the thinset is mixed in a bucket, you can begin applying in the focal-point area first. A fanning motion is a good technique to help you achieve an even thickness of approximately a quarter-inch. Remember to work in small sections as you don’t want the thinset to cure or skin over.

Next, you will be combing the thinset with the notched edge of your trowel. Simply hold it at a slight angle to the wall and comb horizontally. Any excess thinset should return to the bucket. The last step of the thinset application requires you to smoothen out the area with a downward motion. You will want to eliminate any notched lines as it will show through translucent tiles.

Tile Installation

When you place the first tile sheet, do so with gentle pressure. You may need to tap it lightly with a hammer too. While adding the tile sheets, you will want to ensure it looks continuous on the wall. Check to make sure that the tile sheets are at a consistent depth. When the tile sheets are pliable enough, you can remove the paper facing. A moist sponge can help loosen the adhesive.

When you install each tile, you should back-butter it with a layer of thinset before pressing it into place. You will want to do this with your fingers wet to prevent adhesive residues from sticking onto your fingers. Next, let everything cure for at least 48 hours.

Grouting and Caulking

Clean the tiles first with a wet sponge and nylon scrub brush before grouting. You should always achieve a uniformed texture for your premixed urethane grout before applying it with an epoxy grout float. Work in small sections until the entire area is covered. You’re almost there! Using a caulk gun, apply the contents to the perimeter of the backsplash area. Once done, remove all your prep work, reinstall all your electrical receptacles and you’re done.

If you are ready to take on some DIY work, why not start browsing through our inventory of beautiful backsplash tiles to kick off your project?


Read More

water jet mosaic

Read More

Although marble is a type of stone, it is also quite porous, which means that it will easily stain and absorb moisture. It is for this reason that it must be sealed when installed, and it should be resealed roughly every six to twelve months. However, before marble tiles can be sealed, it must first be cut and laid.

How to Cut Marble

During the marble flooring installation, the material will need to be cut. (details) While some people choose to use simple tile snappers, this is not the best option for marble. Tile snappers work well with ceramic tiles, but for marble you will want to choose a wet saw. The wet saw should feature a blade with a diamond tip so that it can cut more efficiently. It is important to exercise caution when slicing marble because it may snap while the grain is within the tile. When slicing marble, you will want to make sure that the cuts are clean.

Laying Down the Marble Tiles

Once the marble is cut, you will next have to lay down the tiles. First you will want to apply and spread the marble mortar within the floor’s center. It should be placed between the chalk lines of the tile pattern. This can be done using a trowel which is notched, and the side of the trowel can be used to create grooves within the mortar which will help it spread evenly. Once this is done you must spend the following ten minutes laying down the marble tile as the mortar will set very quickly.

As you lay down the tiles on top of the mortar, remember to create tile spacers which should be 1/8 inch near the marble corners, as this will ensure they are placed correctly. Double check the location of every tile using a level to verify that each tile’s surface is even. None of the edges should be above the other tiles.

Keep adding the mortar to the small spaces inside the design lines of the snap chalk with the trowel, and put down the marble in the design you want, starting within the center and working your way outward until you reach the walls. The marble tiles should then be left alone for a night so that the thin set can become hardened and cured.

Sealing the Marble

You will start by adding a small bit of the sealing material to a corner tile, so that you can test it to make sure it doesn’t cause discoloration. Wait for it to dry and then compare it to the other tiles. Once you’ve confirmed it won’t cause discoloration you can then use a foam brush to spread it across the floor’s surface. Start from one wall and work backwards so that you don’t step on the marble tiles. Gently add the sealant to each tile, and make sure the layer is thin. You will also need to add the sealant to the grout, and this can be done by running the brush down every grout row. Once this is completed, the floor should be left to dry for 4 hours.


Read More

If you are looking for intricate tiles that provide a luxurious feel, you can never go wrong with marble tiles. What’s more, variations such as tile mosaic combinations work well to provide a truly unique look for your interior design. While marble is an extremely durable material – the ancient Roman temples can attest to that – you should still take the proper steps to clean it well for retaining its natural luster. Want to keep your marble tile installation in a mint condition? Follow these effective and safe cleaning tips!

Dust Mop and Vacuum

The first thing you should do for cleaning marble tiles is to sweep up small debris and dirt using a dust mop. Make sure that the mop has a fluffy, soft head that can trap dust effectively. Microfiber dust mops will do just fine. When you sweep your marble tiles, you will want to prevent the debris from grinding against the stone surface. Ensure that you mop on a weekly basis, and not let grit and dirt build up. If you allow minute scratches to occur on the surface, it will become noticeable over time.

After this, it’s a good practice to vacuum the floor. While doing so, ensure that the wheels are functioning right and they don’t have any rough edges that can scratch your tiles. If your vacuum has any metal attachments, remove them to prevent damage on your beautiful tiles.

Use a Mild and pH Neutral Cleaning Solution

You can wet mop your marble tiles, but ensure that you use a mild cleaning solution that is pH neutral. Acidic substances are known to corrode marble materials, so do avoid using any harsh cleaners. Cleaners that contain vinegar or lemon are a no-no. When you shop at your local hardware store, look for quality cleaners that are suitable for regular use.

When you mop your tiles, you have to wring the mop just enough to avoid sloshing excess water on your floor. In addition, use a dry cloth to wipe down the surfaces to help them dry faster after mopping and prevent water spots from forming.

Throw the Scrubby Sponge Away and Use a Soft Cloth Instead

If you are planning to wipe a small area of your marble tiles by hand, you should never use scrubby sponges that are made out of steel wool. Metal will scratch your marble surfaces! A soft cloth is the perfect alternative for the task at hand.

Clean Up Any Oil-Based Stains, Mold and Organic Material

If your marbles tiles are stained by mold, food or other oil-based products, you should clean the affected area with a cleaning solution, water and a gentle cloth. Check the contents of the cleaning solution and ensure that it has only one of the following: acetone, mineral spirits, ammonia or bleach. You should never combine these substances together as it may produce a lethal gas.

Removing Paint from Your Marble Tiles

If you notice blots of paint on your marble tiles, quickly use a thin blade and some lacquer to gently scrape it off. Take extra care here as you do not want to scratch the natural stone. If you are dealing with thick paint, consider using a commercial-grade paint stripper (heavy liquid) that can be found at local hardware stores to help you rescue your tiles.

Read More

Recent Comments